3M RelyX Temp NE Trmporary Cement (SET)

Key Specification RelyX” Temp NE is an eugenol free, self-curing cement to be used for temporary fixation of dental restorations. By adding Vaseline, the final hardness of the cement can be reduced for easier removal bridges, for example. RelyX temp NE does not affect the polymerization of filing and luting composites. RelyX Temp NE is especially suitable for use on patients with sensitivity to eugenol. These Instructions for Use must be kept for the duration of product use. Fields of Application – Temporary fixation of provisional restorations. – Temporary fixation of crowns, bridges, inlays, and onlays. – Fixation of crowns and bridges onto implant abutments Precautionary Measures For Patients The catalyst paste contains substances that may cause an allergic reaction in case of skin contact in certain individuals. Aviod use of this product in patients with known allergies to colophony and its derivatives. If prolonged contact with oral tissue occurs, flush with large amounts of water. if an allergic reaction occurs, seek medical attention as needed, remove the product, and discontinue future use. For Dental Personnel The catalyst paste contains substances that may cause an allergic reaction in case of skin contact in certain individuals. To reduce the risk of an allergic response, avoid exposure to this material, in particular to the uncured product. If skin contact occurs, wash skin with soap and water. The use of protective gloves and a no-touch technique is recommended. If the catalyst paste contacts the gloves, remove and discard the gloves, wash hands immediately with soap and water, and then re-glove. If an allergic reaction occurs, seek medical attention as needed. 3M MSDSs can be obtained from www.mmm.com, or contact your local subsidiary. Protection of the Pulp In case of deep cavities. apply the protection of the pulp usually employed for temporary fixation. Dispensing and Mixing Use RelyX Temp NE at an ambient temperature of 18° to 23°C/64° to 73°F and relative humidity of 45% to 55%. * Dispense two equal lengths of base paste and catalyst onto a mixing pad. – Overdosing the catalyst will increase the bonding strength and prolong the working time. – Close the tubes immediately after use. Avoid interchanging the tube caps to prevent the possible hardening of the paste in the tube as a result of an unintentional carry-over of the pastes. * The final hardness of the cement can be reduced by adding Vaseline in order to ensure easier removal, e.g., for final bridges. This simultaneously extends the working time. – Dosing: Adda a maximum of 42 mg (the size of a lentil) of Vaseline if a length of 1 cm of base paste (172mg) and of catalyst (78mg) is used. * Use a metal or plastic spatula to thoroughly mix the pastes for 30 seconds until a homogeneous consistency is achieved. Application * Before cementing, clean the cavity surfaces with a water spray and then dry. Water and alcohol residues in the cavity accelerate the setting. * Аpрly а thin layer of cement on the surface to be cemented, anа place the dental restoration with slight pressure. Times The following times apply for an ambient temperature of 23° C/73°F: – Mixing min:sec 0:30 With maximum amount of Vaseline min:sec 0:30 – Working after start of mixing min:sec 1:30 With maximum amount of Vaseline min:sec 2:30 – Setting after start of mixin min:sec 3:30 With maximum amount of Vaseline min:sec 4:00 Setting is accelerated over an ambient temperature of 23° C/73°F and relative humidity of over 55%. Removal of Excessive Material * Use an instrument to remove any excessive material after setting has occurred After Cementation * Thoroughly examine the sulcus of the treated teeth and surrounding dentition. Remove any residual cement from the mouth. Storage and Shelf-Life Store the product at 15°-25°C/59°-77°F. Do not use after the expiry date. Customer Information No person is authorized to provide any information which deviates from the information provided in this instruction sheet. Warranty 3M Deutschland GmbH warrants this product will be free from defects in material and manufacture. 3M Deutschland GmbH MAKES NO OTHER WARRANTIES INCLUDING ANY IMPLED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. User is responsible for determining the suitability of the product for user’s application. If this product is defective with in the warranty period, your exclusive remedy and 3M Deutschland GmbH’s sole obligation shall be repair or replacement of the 3M Deutschland GmbH product. Limitation of liability Except where prohibited by law, 3M Deutschland GmbH will not be liable for any loss or damage arising from this product, whether direct, indirect, special, incidental or consequential, regardless of the theory asserted, including warranty, contract, negligence or strict liability. Packaging 1 Set / Catalyst Paste(13g), Base Paste(30g), Mixing pad(PC)